Picture Day (Where I Stand)

Here's a few pics showing where I stand at the moment.

Phase I: The Dome

This shot shows the dome with the neck tape ripped off, most of the greeblies off and the tape for the neck ladder area and the bottom ring. The horseshoes are in the shot mostly because I store them in the head for now.

Here you can see the top of the head, and what I was talking about with the vinyl stickers bubbling. I'm going to pull them all off, mask it off and paint these panels.

Here's the neck ladder tape, close up. It, along with the brushed steel for the neck ring, is from Tape Brothers (www.tapebrothers.com). I believe they are located in Florida.

This is a large eye greeblie and the peephole sticking up through it. I'm going to repaint the greeblie and probably handpaint the edge of the peephole bezel to match. The only option Lowes had for those was satin nickel, which won't look right with the more silver tone I'm going to paint all these details.

I also decided to grab the smaller peephole style to replace one of the small greeblies on the bottom right.

Phase II: Body

 Sorry it's upside down, but  FIXED PICTURE you can see where I taped off the panels to remain red and ripped/cut out the incorrect flat panel. Upon further inspection I realized I'll need to add material to the LDP area as it was cut too wide. I'm still trying to figure out how the LDP will fit into that space otherwise. I might need to print out the front

 Here's a shot of the back (right side up). The large panel at the top suffered some damage when I was ripping off the magnet system used to keep it in place. It was rather loose, and I don't want that panel to open anyhow. I'm going to fabricate a whole new panel for that location.

I need to take a few minutes and study what goes where for all the details (resin or otherwise) that go in all the now vacant holes. The side vents are still in place because I'm hoping to get them out in one piece. The pocket vents got pretty screwed up when I was taking them out.

I noted that I have one octagon and one power coupling that survived the extraction. The other octagon crumbled and the other power coupling got wrecked along the outer edges.

Here's a shot of the center vents. They're solid resin. They look a bit sloppy to me, so I'm hoping I can clean them up with a good sanding and a repaint.

Here are the base legs that I have. I have to go through the plans to see what stage they are in. I don't really want to start over on these, but I will if I can't figure these out.

You can see the Rockler bearing under there too.

Major Life Update, Game Plan Laid Out

Since the last post I've had a major life change - my first child was born February 19th! This has stopped all project work for the last 3 months.

Even at my last posting I knew it was too ambitious for me to meet the rather small goal I had set of finishing the head. In order to complete this droid, I need to make a checklist of everything that needs to get done, break it down into what I can do in the smallest amount of time and go from there. "What does that mean exactly?" you may ask. Well it's quite simple:

PHASE I

I need to work on R5's head. All the detail needs to be redone.

• Step 1 is complete - I've ripped off all the incorrect neck tape. 
• Step 2 will be to apply the correct neck tape.
• Step 3 is to apply the brushed metal tape to the bottom ring.
• Step 4 is to pop off all the greeblies. This is already 75% done since two of the three large eyes popped off on their own.
• Step 5 is to install the peephole lenses into the large eyes. This one will take a while since I have to figure out how to center them.
• Step 6 is to repaint them all uniformly. The paint job on them looks a tad sloppy.
• Step 7 is to rip off the red stickers on the pie plates and repaint them with red paint. The stickers are bubbly and look like garbage.
• Step 8 is to reapply the red pinstriping, especially around the top of the dome. It's very wavy. The pieces around the breadboxes are fine/good enough for me.
• Step 9 is to reattach the greeblies.
• Step 10 is to wire up the eye lights with blue LEDs and a small battery pack.

PHASE II

The body. I've acquired a partially built body from someone in the R2 Builder's Club (and a rockler bearing!) It was painted in a reverse red pattern much like the one seen here:

I don't know the letter/number designation of this droid but I've seen this configuration before.

• Step 1 - Tape off areas to remain red. Chances are I'm going to repaint the red areas anyway, but for now I'm going to just tape off these areas to save on white paint. This is already done.
• Step 2 - I ripped off/cut out the incorrect unframed panel on the front left. I'm working to create a replacement panel out of styrene. I'm also including any frame modifications I need to make in this step. The LDP doesn't sit correctly, so I'll have to beef up the shelf it sits on and check the clearance for the head.
• Step 3a - Replace all busted panels. Aside from the non-framed panel above, I have a couple of panels I need to replace because I ripped them apart while trying to get at the resin pieces. Mainly the large panel between the "shoulders" on the back and the pieces that go behind the utility arm boxes.
• Step 3b - Get a skirt. I'm not going to screw around with trying to make one when even Bob Ross recommends buying a specific one. (In fact, I'll place that order soon so I don't forget.)
• Step 4a - Paint the body white.
• Step 4b - Paint the detail panels red. Same red I'm using for the dome panels. (I'll also paint the utility arms at this point since I have the paint flowing.)
• Step 5 - replace all broken resin pieces. In trying to take out the resin parts so I could have a relatively clean shell to paint, some of the parts cracked (others shattered completely). I need new side & pocket vents, a new set of octagon ports and I think a new pair of power couplers. I may also want to replace the center vents if the ones I have don't clean up nice. The resin ones I have just look cheap and I might just get the surrounds and cut out the center fins myself.
• Step 6 - Paint all those detail pieces and install them.

PHASE III

Attach Head to Body

This should be a relatively easy phase but it's EXTREMELY important to take as much time as I need. I have a Tom Servo with a small Lazy Susan bearing for his head movement. The head isn't centered on the bearing so I can see it slightly wobbling if I whip his head back and forth. I do not want that to happen to R5! This phase may be something I revisit over and over.

PHASE IV

Legs. I acquired a partially built pair of legs but I may start over.

• Step 1 - Use (or rebuild) the main leg pieces and shoulder hubs.
• Step 2 - Paint main leg pieces white.
• Step 3a - Acquire leg resin detail pieces.
• Step 3b - Acquire beefy ankle kit.
• Step 4 - Paint resin details.
• Step 5 - Assemble.
• Step 6 - Attach to Body. 

PHASE V

Feet/Motors
Right now it's all about research. I know roughly what I need, but getting this refined is paramount. Time is something I can't afford to waste.

PHASE VI

Electronics/Sound
I have a 3rd party PS2 controller. I'm going to study the living hell out of that KISS method that R2 Club Member Asok has laid out. I met him in person at the first DroidCon and was thoroughly impressed with his styrene droid's simplicity. It's what gave me the desire to make my own.

Current Plan

The next few months are insanely busy with a lot of family functions, so if I don't lay out a strategy, I'm doomed.

DOME - Deadline 11/10
I plan on working on the dome in full when I can to have it complete by November 11th. That oddly specific date is the Albany Comic Convention, where I'll be attending as a Tusken Raider for the 501st. I want to have R5's head done so it can be on display there. There's not a LOT to do, but enough that I need to keep on it or I'll never get done.

I ordered the engine turned tape and some brushed chrome tape for the neck and dome ring, respectively (see last post). I have three large peephole kits in brushed nickel as Chris Reiff has done. I need to peel off the vinyl pie plate stickers and paint those red - I think I may pull out the skin panels that need to be this color and do them at the same time. The only other component is the LEDs for the eyes. I'll have to do a bit more research on that just because I don't want to screw it up. I have a very rudimentary understanding of electricity and how to wire things.

I plan on trying to clean up my basement amidst all the other junk I have going on so that I can work on building the router table by Black Friday (Nov 23). I will (hopefully) begin applying the styrene plans to the plastic and cutting out the frame by mid-December. I want to get the body complete by January, minus any resin parts that just aren't available. I'm thinking I'll probably make the vents and coin returns myself.

I'm not looking too much further than that for now.

Tape Ordered

The last place I wanted to order the engine-turned detail vinyl from is perpetually out of stock for the larger size, so I decided to search the Astromech forums to see what other solutions may be available. For some reason, it's difficult to come up with a good list of options, but I eventually found a post from 2010 talking about Tape Brothers.

I went to their site and was pleasantly surprised that they not only still exist, but that the item was still available.

 While I was there I also ordered this brushed chrome tape for the "ring" at the bottom of R5's head. I'll probably use it for his shoulder hubs too since I don't really mind if they are shiny or not.

Machine Turned Annoyance

I just tried to place an order for this stuff:

It's a vinyl sheet that has the correct pattern for R5's "neck" section. I'll have to cut out rectangles and glue them in place since the ladder of my R5's neck doesn't seem to come off. Thing is, the larger size of these sheets is currently sold out. I know it will come back in stock, but it seems like whenever I try to take one step forward, I'm told to have a seat, shut up and enjoy the view.

Oh well. For now I'll work on removing the vinyl pie-piece sections and repainting them. The vinyl bubbles up too much. No matter how I try to smooth it out they come back.

One Piece At A Time...

The latest piece to arrive is the Shoulder Horseshoes.

They are made from solid resin but unfinished. Flashing needs to be sanded off the back then they need to be painted, but otherwise they're looking great!

Fly Casual

This is the blog that never seems to start, or, just like the R5 in A New Hope, blows up as it just starts moving. Rest assured, true believers! R5 will be constructed and assembled in the next year!

Personal stuff this year has been at an all-time high level of crazy. With losing my grandmother, getting my first (and hopefully last) kidney stone, the push for new floors in 4 out of the 6 rooms in the house and -- oh yeah, in case you don't follow me on Facebook -- my wife and I announced that we're having our first child (Feb 20th), it's been a hectic time!

I've received the fiberglass dome that was offered on the R2 Builder's site. It's pretty great, though I need to rework the 'eyes' with lenses and lights (thanks to Chris Reiff for sharing his tricks of the trade!). I plan on making the frame in the next month, though I'm also getting the nagging feeling to just buy an A&A frame.

It's funny that part of what's holding me up, other than the lack of time, space and plain courage to start cutting into the plastic, is that I'm a bit dismayed at the lack of certain resin pieces being offered. I know - cross that bridge when you come to it, don't put the cart before the horse and so on, but it's that stress of "what if it's not available when I'm at the point where I need it?" that eats at me.

Bah - forget all that. I'll assemble the router table, start sticking the plans on the plastic and let loose.